Click here to view and discuss this page in DocCommentXchange. In the future, you will be sent there automatically.
Three operational modes are provided for mirroring:
Synchronous mode is the default. These modes control when and how transactions are recorded on the mirror server, and you set them with the -xp server option.
When choosing a synchronization mode for your database mirroring system, you must determine whether recovery speed or the state of the data is more important when failover occurs.
You can check the database mirroring mode by querying the value of the MirrorMode database property:
SELECT DB_PROPERTY( 'MirrorMode' );
In synchronous mode, committed transactions are guaranteed to be recorded on the mirror server. Should a failure occur on the primary server, no committed transactions are lost when the mirror server takes over. In this mode, the primary server sends transaction log pages to the mirror when a transaction is committed. The mirror server acknowledges that transmission when it has written those pages to its copy of the transaction log. The primary server does not reply to the application until it receives this acknowledgement.
Using synchronous mode provides transaction safety because the operational servers are in a synchronized state, and changes sent to the mirror must be acknowledged before the primary can proceed.
In asynchronous mode, committed transactions are not guaranteed to be recorded on the mirror server. In this mode, the primary server sends transaction log pages to the mirror when a transaction is committed. It does not wait for an acknowledgement from the mirror before replying to the application that the COMMIT has completed. Should a failure occur on the primary server, it is possible that some committed transactions may be lost when the mirror server takes over.
In asyncfullpage (or page) mode, pages are not sent on COMMIT; instead, they are sent when the page is full. This reduces the amount of traffic between the two database servers and improves the performance of the primary server. If the current log page has not been sent to the mirror for the number of seconds specified by the pagetimeout parameter, it is sent even though it is not yet full. The default pagetimeout is 5 seconds. Using this mode provides a limit on how long committed transactions are exposed to being lost if the primary server goes down and the mirror server takes ownership of the database. Asyncfullpage mode implies asynchronous operation, so the primary server does not wait for an acknowledgement from the mirror.
Asynchronous and asyncfullpage mode are faster than synchronous mode, but are less reliable for the above reasons. In asynchronous or asyncfullpage mode, failover from the primary server to the mirror server is not automatic because the mirror server may not have all committed transactions that were applied on the primary server. For this reason, when using one of the asynchronous modes, a mirror server, by default, cannot take ownership of a database when the primary fails. If automatic failover is desirable in this situation (despite the likelihood of lost transactions), set the autofailover option to yes using the -xp server option. Otherwise, when the failed server is restarted, it detects whether transactions were lost. If transactions were lost, it writes a message to the database server message log and shuts down the database. The current database and transaction log must then be replaced using a backup before mirroring can continue.
For information about bringing up a server after it fails in asynchronous or asyncfullpage mode, see Recovering from primary server failure.
It is recommended that you set the -xp autofailover option to yes if you are using asynchronous or asyncfullpage mode. Then, if the primary server goes down, the mirror server automatically takes over as the primary server.
The synchronize_mirror_on_commit option lets you control when database changes are guaranteed to have been sent to a mirror server when running in asynchronous or asyncfullpage mode. When you set this option to On, each COMMIT causes any changes recorded in the transaction log to be sent to the mirror server, and an acknowledgement to be sent by the mirror server to the primary server once the changes are received by the mirror server. The option can be set for specific transactions using SET TEMPORARY OPTION. It may also be useful to set the option for specific applications by examining the APPINFO string in a login procedure.
SQL Anywhere supports system events that fire when failover occurs in a database mirroring system, regardless of which mode you are using. You can use these events for such tasks as notifying the administrator when failover occurs. See Database mirroring system events.
State information files
|Send feedback about this page via email or DocCommentXchange||Copyright © 2008, iAnywhere Solutions, Inc. - SQL Anywhere 11.0.0|